DAYBETTER Under Cabinet Lights, 6 PCS Under Cabinet Lighting with Remote, Dimmable LED Strip Lights for Bedroom, LED Lights for Kitchen Cabinet, Counter Shelf 2700K-6500K Warm to Daylight White, 9.8ft

Great LED light strip that gets the job done
As like many other comments, “beautiful and easy to install.” Here’s what I can add.Making your own LED light strip is actually easy as long as you know how to solder. Just cut to length your roll of lights only through the middle of a column of contacts, attach LED driver to strip, attach strip to location, and attach driver to power source (plug-able method is the safest). These light strips by DayBetter are even easier as the strip is already divided into six segments roughly 1ft 7-8in long that comes ready to plug into each other for a maximum length of 9.8ft. The only downside is you give up on other conveniences; the controller/driver comes already attached to the 1st segment with roughly about 4in of cable, and the power cord is roughly 2ft 10in only. So you need a convenient outlet close by (or use an extension cord). On the plus side, the plug/power-adapter is small and compact and looks pretty good on the wall outlet.Things not explained:▪︎ The picture of the box contents (as of September 2025) is complete, but not descriptive. The 6 Light strip segments are depicted bottom left. The white srips on top right are connection extensions for between the lighted segments. Five 6in extensions, and three 3in U connectors (the plugs both face on one side). These connectors are foldable (flat) copper wires (but try not to bend and unbend too many times).▪︎ The LED strip segments can be cut to shorter lengths, but ONLY where the column of contact pads are. They look like a stack of copper bars.I recommend getting strip light channels to house these lights. The LED light strips are essentially bare circuit boards, which means there are potential exposed points that can be shorted. I have sweaty hands, and even with the lights off, I can put my finger between two lights or circuit chips, and two or more lights near my finger will weakly light up. There a several other reasons to use light channels, but I’m not going to elaborate on them here.Issues:▪︎ The controller cord and power cord is rather too short.▪︎ No known official way to order more controllers & power adapters to use with unused light strip segments.▪︎ The unpairing and pairing does not really do anything. After unpairing, the lights only dimmed and brightened (not blink as it should), and afterwards I can still control the lights with the remote. In fact, I’ve tried the remote on another set of lights that I have not done the unpair/pair routine (and was still controlled by its own remote) and I was able to control the other lights straight off the bat.Last note:▪︎ The recieving female plugs on the connection extensions are out-of-the-factory new, and may not be easy to connect with its counterpart. Before making the initial plug-in, turn the two plugs 90° to each other so that you can push a single pin into each of the recieving hole one at a time (being careful to not poke yourself) to break in the plug.All and all, I’m very satisfied with this LED strip light. I, in fact, have more than one of them.

Great lighting solution for desk lighting
I wanted some light strips to attach to the bottom of my monitors to provide focused lighting for my work desk. These are perfect!They attached easily, the adhesion is great and each strip is an excellent length for each monitor. The connectors were easy to attach as well. The strips are lightweight.There are multiple types of lights as well as light modes, so you’re sure to find on that works perfectly for you.You can choose the color temperature from 6 presets, as well as adjust the brightness level. These also have a sunrise, sunset and night mode.Another fun option are the dynamic modes – flashing, gradient, jump, and 2 breathing modes. It’s great to have this option, but as I’m sure you can imagine, I won’t be using them at my work desk LOLIf I was looking for white lighting for a display, these would also be perfect.All around solid choice for LED lighting with multiple options.

For the price these are very great. I would buy them again if I needed it.
Very easy set up. It was perfect length for what I needed it for, and I love how you can change the tone of the light. These are dimmable, which I love and the double-sided tape that sticks them to the cabinets is very strong. I have not had an issue with these coming off and they’ve been on my cabinets for going on three months now. Keep in mind once I install these I realize you can see the reflection from my granite countertops, so make sure you put them straight when installing them.. I put mine straight, but I could see how someone would overlook that and end up having to take it off and put it back on, which would make the adhesive less functional